Upholstery 101 (week 11) The Finale!
Hello, and welcome back...in case you are new here...this is an on-going upholstery series. To start at the beginning, go here.
First, the chair
It's done! This is like skipping the meal, and going to dessert first...now here are my last steps
This is where I started
To finish the inside arms, I placed a strip of fabric, just like I did the top arm piece here
...using the cardboard strip again, make a fold on the left
...and bring down
Just like the lining done here, fold and staple under the arm
This is what it looks like. The other end will get covered with finished fabric
For the side, a light-weight piece of cardboard works great. I used yellow poster-board so that you could see it clearly....it doesn't matter...it won't show. Tack it in place. This keeps the batting in place.
...I added a layer of batting, stapling under the arm...
...then flipping it into place, and tacking it all around
For the back of the chair...and to "finish piping"....this works great for pillows too...cut one end bluntly. Open the seam on the piping
exposing the cording....leaving plenty of material, cut the cording to meet exactly with the blunt edge
Fold under the extra material...
...and wrap it around the blunt edge piece. This is the most professional way to finish piping on a pillow, cushion....whatever! In this case, staple it into place
I used a light weight piece of foam for the back...tack, tack
Keeping with my Mckenzie-Childs inspiration, I am using camel velvet for the back and sides. Like you have seen so many times, tack the top, bottom,
side to side...pulling at each point
Trim
For the sides, with right sides together, I put a few pins in at the top to hold the fabric in place
more cardboard stripping following the staple line (and covering all the top staples) that was made on the back piece
Staple all the way down, should look like stitches
Fold over, to reveal the finished back seam
Working top and bottom, pull and staple
Keep pressure on the fabric to work out any wrinkles
Trim...add whatever type fringe, gimp, or welting you desire...like I did in this post
Make sure to hide all the staples, and embellish where it is needed
...and admire your results
Especially those cute brass(?) feet Ididn't polish here
The end...Class is dismissed! Now I am onto my basement. What are you working on?
First, the chair
It's done! This is like skipping the meal, and going to dessert first...now here are my last steps
This is where I started
To finish the inside arms, I placed a strip of fabric, just like I did the top arm piece here
...using the cardboard strip again, make a fold on the left
...and bring down
Just like the lining done here, fold and staple under the arm
This is what it looks like. The other end will get covered with finished fabric
For the side, a light-weight piece of cardboard works great. I used yellow poster-board so that you could see it clearly....it doesn't matter...it won't show. Tack it in place. This keeps the batting in place.
...I added a layer of batting, stapling under the arm...
...then flipping it into place, and tacking it all around
For the back of the chair...and to "finish piping"....this works great for pillows too...cut one end bluntly. Open the seam on the piping
exposing the cording....leaving plenty of material, cut the cording to meet exactly with the blunt edge
Fold under the extra material...
...and wrap it around the blunt edge piece. This is the most professional way to finish piping on a pillow, cushion....whatever! In this case, staple it into place
I used a light weight piece of foam for the back...tack, tack
Keeping with my Mckenzie-Childs inspiration, I am using camel velvet for the back and sides. Like you have seen so many times, tack the top, bottom,
side to side...pulling at each point
Trim
For the sides, with right sides together, I put a few pins in at the top to hold the fabric in place
more cardboard stripping following the staple line (and covering all the top staples) that was made on the back piece
Staple all the way down, should look like stitches
Fold over, to reveal the finished back seam
Working top and bottom, pull and staple
Keep pressure on the fabric to work out any wrinkles
Trim...add whatever type fringe, gimp, or welting you desire...like I did in this post
Make sure to hide all the staples, and embellish where it is needed
...and admire your results
Especially those cute brass(?) feet I
The end...Class is dismissed! Now I am onto my basement. What are you working on?